desktop_station_s_serial_communication_specification
差分
このページの2つのバージョン間の差分を表示します。
両方とも前のリビジョン前のリビジョン次のリビジョン | 前のリビジョン | ||
desktop_station_s_serial_communication_specification [2017/06/05 06:24] – [Communication procedure] yaasan | desktop_station_s_serial_communication_specification [2023/12/26 21:00] (現在) – [外部操作の注意点] yaasan | ||
---|---|---|---|
行 22: | 行 22: | ||
コマンドの構造は、「コマンド名(引数1, | コマンドの構造は、「コマンド名(引数1, | ||
+ | |||
+ | コマンドを送る場合、200 Okの応答からウェイトを最低100ms以上置いてください。内部で処理を行ってDCCパルス生成器を確実に動作させるために必要です。 | ||
===== Command list ===== | ===== Command list ===== | ||
行 52: | 行 54: | ||
|CV Value | 0-255 | Locomotive' | |CV Value | 0-255 | Locomotive' | ||
+ | 以下のテーブルは、ロコとポイントのアドレス(1-65535)の意味をあらわしてます。\\ | ||
The following table describes Locomotive' | The following table describes Locomotive' | ||
行 69: | 行 72: | ||
|302 receive timeout | Command is not received fully in the enough time. | | |302 receive timeout | Command is not received fully in the enough time. | | ||
|303 Unknown error | Unknown issue happens. | | |303 Unknown error | Unknown issue happens. | | ||
+ | |@PWR, | ||
+ | |@DIR, | ||
+ | |@FNC, | ||
+ | |@ACC, | ||
+ | |@SPD, | ||
===== Communication procedure ===== | ===== Communication procedure ===== | ||
行 83: | 行 91: | ||
===== Example of communication log ===== | ===== Example of communication log ===== | ||
+ | |||
+ | 以下は、通信ログの例です。setPing()を投げて生存確認をしてから、setPower(1)で線路電源のON、そのあとはコマンドを打てばその通りにDCC信号が出力されます。 | ||
< | < | ||
行 121: | 行 131: | ||
[RECV]200 Ok | [RECV]200 Ok | ||
</ | </ | ||
+ | |||
+ | ===== 外部操作の注意点 ===== | ||
+ | |||
+ | * 本体でDCC電源のON/ | ||
+ | * 本仕様書は随時更新されます。また、予告なしに仕様が変更される場合があります。 | ||
+ | * 本仕様書に記載の事項で、自動運転装置をビジネス・業務としてインテグレーションすることは自由ですが、当社は一切の動作保証、環境に起因するサポートをいたしません。ビジネス・業務用途での個別サポートを要求される場合には、サポート契約を申し込みください。サポート契約外のサポートについては一切お断りいたします。 | ||
+ | |||
+ | |||
+ | |||
+ |
desktop_station_s_serial_communication_specification.1496611458.txt.gz · 最終更新: 2017/06/05 06:24 by yaasan